The log action in MikroTik's firewall does not block or drop packets. Instead, it generates a log entry for packets that match the rule and passes the packet to the next rule in the chain. It is used for monitoring, debugging, or auditing network behavior.
MTCNA Official Course Material – Firewall Filters:
“The action 'log' creates a log entry when a packet matches the rule. It does not terminate or alter the packet's flow. The packet continues to be processed by subsequent rules.”
René Meneses MTCNA Study Guide – Firewall Logging:
“Log action is used to generate logs for matched packets. It does not block or modify traffic.”
MikroTik Wiki – Firewall Actions:
“log – This action writes matching packets to the log. Logging rules have no effect on the packet’s behavior.”
Hence, Option D is correct: It logs the packet, nothing more.
Final Answer: DQUESTION NO: 86 [Firewall]
Which of the following is true for connection tracking?
A. Connection tracking must be enabled for NAT'ed network
B. Enabling connection tracking reduces CPU usage in RouterOS
C. Disable connection tracking for mangle to work
D. Connection tracking must be enabled to be able to use all firewall features
Answer: D
Connection tracking (conntrack) is a feature that enables RouterOS to monitor and manage the state of all network connections passing through the router. It is essential for features like NAT, stateful firewalling, and proper use of mangle and filter rules.
MTCNA Course Material – Connection Tracking:
“Most firewall and NAT functionality depends on connection tracking being enabled. Without connection tracking, many features (like NAT) won’t function properly.”
René Meneses MTCNA Study Guide – Firewall Section:
“Connection tracking is required for NAT and most firewall filters. When disabled, connection-state-based filtering or NAT is not possible.”
Terry Combs MTCNA Notes – Conntrack Section:
“Conntrack must be enabled to use full firewall capabilities, including NAT and filtering by connection states like established and related.”
Option A is partially true but not complete.
Option B is incorrect – conntrack may increase CPU load due to session tracking.
Option C is incorrect – mangle rules often depend on connection marks which require conntrack.
Only Option D accurately captures the critical requirement of connection tracking.
Final Answer: DQUESTION NO: 87 [RouterOS Introduction]
Which of the following keystrokes enables safe mode in console?
A. Ctrl+x
B. Ctrl+c
C. Ctrl+d
D. Ctrl+s
Answer: D
Safe Mode in MikroTik CLI is a protective mode that helps revert any unintended changes if you get disconnected. It is activated by pressing Ctrl+X in older versions, but the current standard keybinding for enabling safe mode is Ctrl+S.
MTCNA Course Material – Safe Mode:
“To enable safe mode in the terminal, press Ctrl+S. A confirmation [Safe Mode] will appear in the prompt. If the terminal is closed or disconnected, the changes are rolled back.”
René Meneses MTCNA Study Guide – Terminal Commands:
“Safe Mode can be activated using Ctrl+S. This is useful during remote configuration. It reverts changes if the terminal is closed.”
MikroTik Wiki – Safe Mode Section:
“To enter safe mode, press Ctrl+S in CLI. This ensures configuration rollback if disconnected.”
Other options:
Ctrl+C terminates commands or CLI input
Ctrl+X may not activate safe mode in newer versions
Ctrl+D is used to log out in some Unix-like terminals
Correct answer: Ctrl+S
Final Answer: DQUESTION NO: 88 [Wireless]
Select minimal set of software packages in RouterOS required to configure a wireless AP:
A. Wireless
B. advanced-tools
C. dhcp
D. routing
E. system
Answer: A
To configure a wireless access point (AP) in RouterOS, the only required software package is wireless. All other functionalities like DHCP or routing are optional depending on the network setup. The system package is always present and not removable, so it's not listed as a required dependency in package selection.
MTCNA Course Material – Wireless Configuration Basics:
“Wireless functionality is provided by the wireless package. Without it, no wireless interfaces are present or configurable.”
René Meneses MTCNA Guide – Wireless Module:
“Only the wireless package is required to configure an AP. DHCP is used optionally for IP address assignment.”
MikroTik Wiki – Packages:
“The wireless package is responsible for enabling WLAN interfaces and features such as AP mode, client mode, and security.”
Other packages:
advanced-tools: includes tools like bandwidth-test and traffic generator
dhcp: only needed if the router is issuing IPs
routing: required for static/dynamic routing but not AP setup
Only Option A is required.
Submit