Pass the CompTIA Network+ N10-009 Questions and answers with ValidTests

A warm site is a compromise between a hot site and a cold site, providing a balance between cost and recovery time. It is partially equipped with the necessary hardware, software, and infrastructure, allowing for a quicker recovery compared to a cold site but at a lower cost than a hot site.

Recovery Time: Warm sites can be operational within hours to a day, making them suitable for non-critical applications that can tolerate short downtimes.

Cost-Effectiveness: Warm sites are more economical than hot sites as they do not require all systems to be fully operational at all times.

Network References:

CompTIA Network+ N10-007 Official Certification Guide: Discusses disaster recovery strategies and the different types of recovery sites.

Cisco Networking Academy: Provides training on disaster recovery planning and site selection.

Network+ Certification All-in-One Exam Guide: Explains the characteristics of hot, warm, and cold sites and their use cases in disaster recovery planning.

Warm sites offer a practical solution for maintaining business continuity for non-critical applications, balancing the need for availability with cost considerations.

A content filter blocks access to specific websites based on category, URL, or keywords. This is the best solution to restrict gambling websites.

Breakdown of Options:

A. ACLs – Control network access, not specific web content.

B. Content filter – ✅ Correct answer. Used to block access to unwanted websites.

C. Port security – Prevents unauthorized device connections, not web traffic filtering.

D. Screened subnet – A DMZ isolates public-facing servers, not user restrictions.

The longest prefix match is a routing concept used to find the most specific route to a destination IP address. The routing table performs this calculation to determine the exit interface for a packet, ensuring the most accurate delivery. The document explains:

“Routers use the longest prefix match when searching the routing table to determine the best path for an IP packet. This ensures that the most specific (and thus optimal) route is chosen, based on the destination IP address.”

If the user cannot communicate with 192.168.10.1, they might be on a different subnet. Changing the subnet mask to 255.255.255.0 ensures the user and the file server are in the same subnet.

Breakdown of Options:

A. Changing the IPv4 address to 192.168.10.1 – This would conflict with the server's IP.

B. Changing the subnet mask to 255.255.255.0 – ✅ Correct answer. Ensures both the user and the server are on the same subnet.

C. Changing the DNS servers – DNS does not affect local network connectivity.

D. Changing the physical address – The MAC address does not impact subnet communication.

After implementing a solution and putting preventive measures in place, the next step is to verify that the system is functioning correctly. This ensures that the issue has been fully resolved.

=================

A large number of collisions and input errors typically indicates a duplex mismatch, such as when one device is set to full duplex and the other to half duplex. This leads to communication issues and poor performance. The document explains:

“Collisions and input errors are clear signs of duplex mismatches… typically caused when one device operates in half duplex while the other is in full duplex, causing performance and connectivity issues.”

•nslookup allows querying DNS records to verify if the new server is correctly resolving domain names.

•ping (A) tests basic connectivity, not DNS configuration.

•tracert (B) shows network path latency but doesn’t test DNS.

•tcpdump (C) captures packets but isn’t ideal for DNS verification.

????Reference: CompTIA Network+ N10-009 Official Documentation – DNS Testing Tools.

Link Layer Discovery Protocol (LLDP) is a network protocol used for discovering devices and their capabilities on a local area network, primarily at the data link layer (Layer 2). It helps in identifying the connected switch and the specific port to which a device is connected. When troubleshooting a VoIP handset connection, the technician can use LLDP to determine the exact switch and port where the handset is connected. This protocol is widely used in network management to facilitate the discovery of network topology and simplify troubleshooting.

Other options such as IKE (Internet Key Exchange), VLAN (Virtual LAN), and netstat (network statistics) are not suitable for identifying the switch and port information. IKE is used in setting up secure IPsec connections, VLAN is used for segmenting networks, and netstat provides information about active connections and listening ports on a host but not for discovering switch port details.

A rogue DHCP server occurs when an unauthorized or misconfigured DHCP server assigns incorrect IP addresses, default gateways, or DNS settings to clients.

•In this scenario:

•The user can ping the gateway, meaning local network communication is working.

•However, they cannot access network resources, which suggests incorrect IP configuration (likely due to a rogue DHCP server assigning the wrong gateway or DNS).

•Why not the other options?

•VLAN hopping (A): This is an attack that exploits VLAN configurations to gain access to unauthorized VLANs. It would not typically cause multiple users to lose network access.

•Distributed DoS (C): A DDoS attack floods a network or service with traffic, but this issue is more likely misconfigured IP settings than an actual attack.

•Evil twin (D): This refers to a fraudulent Wi-Fi network mimicking a legitimate one. Since the users are on a wired network (ipconfig output checked), this is not applicable.

Shoulder surfing is a social engineering attack where attackers observe someone’s private information by looking over their shoulder or using tools like cameras to capture input.

From Andrew Ramdayal’s guide:

“Shoulder surfing is the act of watching someone enter confidential information, such as PINs or passwords, often using direct line-of-sight or surveillance equipment.”

Asymmetrical routing occurs when packets take different paths to and from the destination, leading to instability in network communication. The use of two different MPLS providers with OSPF can lead to this type of routing issue, especially if the paths aren't carefully configured and managed. This can cause unexpected routing behaviors and instability in a dual-WAN setup. (Reference: CompTIA Network+ Study Guide, Chapter on Network Routing)

Port security is a Layer 2 security feature that restricts the number of devices connecting to a network switch port. It helps prevent unauthorized devices, such as an unmanaged switch, from being connected to the network.

How Port Security Works:

Limits the number of MAC addresses that can connect to a port.

Can shut down or restrict the port if an unauthorized device is detected.

Prevents users from plugging in unauthorized networking equipment (e.g., unmanaged switches, hubs).

Incorrect Options:

A. Screened Subnet: A screened subnet (DMZ) is used for isolating external-facing servers, not for controlling unauthorized network connections.

B. 802.1X: Provides authentication for devices but requires a RADIUS server, which is a more complex solution than port security.

C. MAC Filtering: Controls which MAC addresses can connect but is difficult to manage and can be spoofed.

If the user cannot communicate with 192.168.10.1, they might be on a different subnet. Changing the subnet mask to 255.255.255.0 ensures the user and the file server are in the same subnet.

Breakdown of Options:

A. Changing the IPv4 address to 192.168.10.1 – This would conflict with the server's IP.

B. Changing the subnet mask to 255.255.255.0 – ✅ Correct answer. Ensures both the user and the server are on the same subnet.

C. Changing the DNS servers – DNS does not affect local network connectivity.

D. Changing the physical address – The MAC address does not impact subnet communication.

IPsec (Internet Protocol Security) is the most secure way to provide site-to-site connectivity. It provides robust security services, such as data integrity, authentication, and encryption, ensuringthat data sent across the network is protected from interception and tampering. Unlike other options, IPsec operates at the network layer and can secure all traffic that crosses the IP network, making it the most comprehensive and secure choice for site-to-site VPNs.References: CompTIA Network+ study materials and NIST Special Publication 800-77.

The tracert (Traceroute) command is used to determine the path packets take from the source to the destination. It helps in identifying routing issues by showing each hop the packets pass through, along with the time taken for each hop. This command can pinpoint where the connection is failing or experiencing delays, making it an essential tool for troubleshooting routing issues.References: CompTIA Network+ study materials and common network troubleshooting commands. ​