Pass the CWNP CWAP Wi-Fi Analysis CWAP-405 Questions and answers with ValidTests

The first step in any troubleshooting process is to define the problem. This involves gathering information from various sources, such as users, network administrators, network documentation, and network monitoring tools. Defining the problem helps to narrow down the scope of the issue and identify the symptoms, causes, and effects of the problem12 References:

CWAP-403 Study Guide, Chapter 1: Troubleshooting Methodology, page 7

CWAP-403 Objectives, Section 1.1: Define the problem

The best way to test the theory of microwave interference from the New York office is to use a remote spectrum analyzer. By placing one of the London APs into spectrum analyzer mode, you can capture and analyze the RF spectrum in the London office over lunch time. You can then look for any signs of microwave interference, such as high duty cycle, high amplitude, or frequency hopping on the 2.4 GHz band. This method does not require any physical access to the microwave or any changes to its frequency. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 64

The data rate at which the PHY preamble was transmitted is 6 Mbps. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to detect and synchronize with the signal. The PHY preamble is always transmitted at a fixed data rate that depends on the type of PPDU (e.g., OFDM, HT, VHT, HE). For an 802.1 lac data frame on channel 52, which uses VHT PPDUs, the data rate for the PHY preamble is 6 Mbps. This data rate does not depend on MCS (Modulation and Coding Scheme), which only affects the data rate for the PSDU. References: [Wireless Analysis Professional Study Guide CWAP-405], Chapter 4: 802.11 Physical Layer, page 99-100

The CRC is calculated over the MAC Header and Frame Body only. The CRC (Cyclic Redundancy Check) is a 32-bit value that is used for error detection in wireless transmissions. The CRC is calculated over the MAC Header and Frame Body of a PSDU, which are the parts of the data unit that contain information such as source and destination addresses, frame type, frame control, sequence number, payload, etc. The CRC is appended to the end of the PSDU as a FCS (Frame Check Sequence) field. The CRC is not calculated over the PHY Header or PHY Preamble, which are parts of the PPDU that contain information such as modulation, coding, data rate, etc. The PHY Header and PHY Preamble are added or removed by the PHY layer during the conversion between PSDU and PPDU. References: [Wireless Analysis Professional Study Guide CWAP-405], Chapter 4: 802.11 Physical Layer, page 97-98

The Swept Spectrogram plot is a spectrum analysis plot that shows the RF power present at a particular frequency over the course of time. It can help identify trends and patterns in the RF spectrum over a longer period of time. It can also show how the RF environment changes over time and how different sources of RF signals affect each other. The other options are not correct, as they describe different types of plots or information that are not related to the Swept Spectrogram plot. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 72-73

One way to confirm if you have missing packets in your packet capture is to look for gaps in the sequence number in MAC headers. The sequence number is a 12-bit field in the MAC header that is used to identify and order data frames within a traffic stream. The sequence number is incremented by one for each new data frame transmitted by a STA, except for retransmissions, fragments, and control frames. The sequence number can range from 0 to 4095, and then wraps around to 0. If you see a jump or a gap in the sequence number between two consecutive data frames from the same STA, it means that you have missed some packets in between. The other options are not correct, as they do not confirm if you have missing packets in your packet capture. CRC errored packets are packets that have been corrupted during transmission and have failed the error detection check. Protocol analyzers may show the number of CRC errored packets in their statistics view, but not the number of missing packets. Retransmissions are an indication of packet loss or collision, but not necessarily of missing packets in your capture. References: [Wireless Analysis Professional Study Guide CWAP-405], Chapter 5: 802.11 MAC Sublayer, page 114-115