Weekend Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: simple70

Pass the F5 TMOS Administration 201 Questions and answers with ValidTests

Viewing page 1 out of 7 pages
Viewing questions 1-10 out of questions
Questions # 1:

Refer to the exhibit

Question # 1

Question # 1

The network team creates a new VLAN on the switches. The BIG-IP Administrator needs to create a

configuration on the BIG-IP device. The BIG-IP Administrator creates a new VLAN and Self IP, but the

servers on the new VLAN are NOT reachable from the BIG-IP device.

Which action should the BIG-IP Administrators to resolve this issue?

Options:

A.

Set Port Lockdown of Set IP to Allow All

B.

Change Auto Last Hop to enabled

C.

Assign a physical interface to the new VLAN

D.

Create a Floating Set IP Address

Expert Solution
Questions # 2:

A BIG-IP Administrator makes a configuration change to the BIG-IP device. Which file logs the message regarding the configuration change?

Options:

A.

/var/log/messages

B.

/var/log/audit

C.

/var/log/user.log

D.

/var/log/secure

Expert Solution
Questions # 3:

A Virtual Server uses an iRule to send traffic to pool members depending on the URI. The BIG-IP

Administrator needs to modify the pool member in the iRule.

Which event declaration does the BIG-IP Administrator need to change to accomplish this?

Options:

A.

CLIENT_ACCEPTED

B.

HTTP_RESPONSE

C.

HTTP_REQUEST

D.

SERVER_CONNECTED

Expert Solution
Questions # 4:

Users report that traffic is negatively affected every time a BIG-IP device fails over. The traffic becomes

stabilized after a few minutes.

What should the BIG-IP Administrator do to reduce the impact of future failovers?

Options:

A.

Enable Failover Multicast Configuration

B.

Set up Failover Method to HA Order

C.

Configure MAC Masquerade

D.

Configure a global SNAT Listener

Expert Solution
Questions # 5:

When can a single virtual server be associated with multiple profiles?

Options:

A.

Never. Each virtual server has a maximum of one profile.

B.

Often. Profiles work on different layers and combining profiles is common.

C.

Rarely. One combination, using both the TCP and HTTP profile does occur, but it is the exception.

D.

Unlimited. Profiles can work together in any combination to ensure that all traffic types are supported in a given virtual server.

Expert Solution
Questions # 6:

Active connections to pool members are unevenly distributed. The load balancing method is Least Connections (member) Priority Group Activation is disabled. What is a potential cause of the event distribution?

Options:

A.

Priority Group Activation is disabled

B.

SSL Profile Server is applied

C.

Persistence profile is applied

D.

incorrect load balancing method

Expert Solution
Questions # 7:

A BIG-IP Administrator is unable to connect to the management interface via HTTPS. What is a possible reason for this issue?

Options:

A.

The port lockdown setting is configured to Allow None.

B.

An incorrect management route is specified.

C.

The IP address of the device used to access the management interface is NOT included in the "P Allow" list in the Configuration Utility.

D.

The IP address of the device used to access the management interface is NOT included in the "httpd Allow" list in the CLI.

Expert Solution
Questions # 8:

Which three properties can be assigned to nodes? (Choose three.)

Options:

A.

ratio values

B.

priority values

C.

health monitors

D.

connection limits

E.

loadbalancing mode

Expert Solution
Questions # 9:

Refer to the exhibit.

Question # 9

Question # 9

A BIG-IP Administrator creates a new Virtual Server to load balance SSH traffic. Users are unable to log on to the servers.

What should the BIG-IP Administrator do to resolve the issue?

Options:

A.

Set Protocol to UDP

B.

Set HTTP Profile to None

C.

Set Source Address to 10.1.1.2

D.

Set Destination Addresses/Mask to 0.0.0.0/0

Expert Solution
Questions # 10:

Which statement is true about the synchronization process, as performed by the Configuration Utility or by typing b config sync all?

Options:

A.

The process should always be run from the standby system.

B.

The process should always be run from the system with the latest configuration.

C.

The two /config/bigip.conf configuration files are synchronized (made identical) each time the process is run.

D.

Multiple files, including /config/bigip.conf and /config/bigip_base.conf, are synchronized (made identical) each time the process is run.

Expert Solution
Viewing page 1 out of 7 pages
Viewing questions 1-10 out of questions