Weekend Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: simple70

Discussions
  1. Home
  2. HP
  3. Aruba Certified Switching Associate (ACSA) V1
  4. HPE6-A72
  5. Aruba Certified Switching Associate Exam Questions and Answers

Pass the HP Aruba Certified Switching Associate (ACSA) V1 HPE6-A72 Questions and answers with ValidTests

Exam HPE6-A72 All Questions
Exam HPE6-A72 Premium Access

View all detail and faqs for the HPE6-A72 exam

Go to Exam
Viewing page 1 out of 4 pages
Viewing questions 1-10 out of questions
Questions # 1:

What does link aggregation provide? (Select two.)

Options:

A.

improved bandwidth between switches

B.

faster convergence than spanning-tree

C.

support for up to 2 active ports to be bundled together

D.

disables spanning-tree between switches

E.

no load balancing

Expert Solution
Questions # 2:

Refer to the exhibit.

Question # 2

Which command produces the above output?

Options:

A.

show interface port 1/1/10 trunk

B.

show vlan port 1/1/10

C.

show trunk port 1/1/10 extended

D.

show interface port 1/1/10 switchport

Expert Solution
Questions # 3:

The customer has 778 developers testing computer games on the network.

Which two actions resolve Broadcast storms? (Choose two.)

Options:

A.

Manually disable the redundant link to immediately resolve the impacted portion of the network.

B.

Utilize Spanning Tree to dynamically disable all redundant links in a segment.

C.

Setting switch ports to half-duplex will resolve Broadcast storms using Carrier Sense Multiple-Access Collision Detection (CSMA/CD).

D.

Enable single Area Open Shortest Path First (OSPF) on all Layer 2 switches, but do not enable routing.

E.

Utilize Spanning Tree to dynamically block Designated ports in addition to Alternate ports.

Expert Solution
Questions # 4:

Aruba Access Points tunnel traffic in a campus to the Mobility Controller using which protocol?

Options:

A.

Control and Provisioning of Wireless Access Points (CAPWAP)

B.

Generic Routing Encapsulation (GRE)

C.

Lightweight Access Point Protocol (LWAPP)

D.

Process Application Programming Interface (PAPI)

Expert Solution
Questions # 5:

What are two mechanisms supported on AOS-CX 6300 switches used in Multi-active Detection to determine the status of the Primary member? (Choose two.)

Options:

A.

Management interface split detection

B.

Peer switch-based detection

C.

Loopback keepalives

D.

ARP-based

E.

BFD

Expert Solution
Questions # 6:

Match each network protocol to the correct server listening port. Not all answers will be used.

Question # 6

Options:

Expert Solution
Questions # 7:

What is the correct description of a Multi-Layer Switch?

Options:

A.

a switch with Layer 3 routing capabilities but lacks any Layer 1 features as a consequence

B.

any switch that supports PoE, LLDP-MED and Flow Control

C.

has all the functionality of a Layer 2 switch and most of the functionality of a Layer 3 router

D.

multi-Layer refers specifically to using chassis switches with several line cards over stack port switches

Expert Solution
Questions # 8:

Refer to the exhibit.

Question # 8

What configuration is needed in order for "show LLDP configuration" to show this output?

Options:

A.

none; LLDP is enabled by default on Aruba switches

B.

configuring LLDP both globally and on the interfaces

C.

enabling LLDP on the interfaces only

D.

configuring LLDP globally only

Expert Solution
Questions # 9:

Which Ethernet port combination does the Aruba 5400R ZL2 switch series support?

Options:

A.

10/100 Megabit Ethernet, Gigabit Ethernet, and 100 Gigabit Ethernet

B.

Gigabit Ethernet, 25 Gigabit Ethernet, and 40 Gigabit Ethernet

C.

10/100 Megabit Ethernet, Gigabit Ethernet, 25 Gigabit Ethernet, and 100 Gigabit Ethernet

D.

10/100 Megabit Ethernet, Gigabit Ethernet, and 40 Gigabit Ethernet

Expert Solution
Questions # 10:

What command will save your configuration on an Aruba AOS-CX switch so that your changes automatically load on next reboot?

Options:

A.

copy running-config checkpoint startup-config

B.

copy startup-config running-config

C.

copy running-config initial-checkpoint

D.

copy running-config default

Expert Solution
Viewing page 1 out of 4 pages
Viewing questions 1-10 out of questions