Pre-Summer Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: validbest

Pass the Netapp Other NS0-163 Questions and answers with ValidTests

Exam NS0-163 All Questions
Exam NS0-163 Premium Access

View all detail and faqs for the NS0-163 exam

Viewing page 2 out of 6 pages
Viewing questions 11-20 out of questions
Questions # 11:

Alter a SnapRestore reversion of a volume, incremental backup and restore operations on the file or volume cannot rely on the timestamps to determine what data needs to be backed up or restored. Which one of the following is the most likely course of action to take to ensure correct incremental backups?

Options:

A.

Perform a base-level backup of the volume after you restore it.

B.

Reboot the storage appliance to reset timestamps back to their original times before the reversion.

C.

Take a new snapshot of the volume to create new base-level timestamps for the incremental backup.

D.

First perform choice c and then choice a.

Expert Solution
Questions # 12:

Exhibit:

Question # 12

To remove a cluster setup, you must perform the steps displayed in the exhibit.

Options:

A.

True

B.

False

Expert Solution
Questions # 13:

The snapvault update command is only available on the secondary system.

Options:

A.

True

B.

False

Expert Solution
Questions # 14:

Refer to the exhibit.

Question # 14

An administrator creates a new qtree and an associated export policy. When the client tries to connect, they are denied.

What should the administrator do?

Options:

A.

Update the superuser entry lo "any" in the volume export-policy

B.

Replace the IP with the client hostname in the qtree export policy

C.

Add the new host IP with at least read access to the volume export-policy

D.

Add a new rule in the qtree export policy in allow read-write access for the new host

Expert Solution
Questions # 15:

If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank

Options:

A.

1

B.

3

C.

4

D.

2

Expert Solution
Questions # 16:

An administrator enables the NFS protocol on an SVM and creates a volume to be used as a datastore in a VMware environment. After a rescan, the volume is not visible on the ESXi hosts.

What must the administrator validate to resolve this problem?

Options:

A.

Export policy

B.

Name service

C.

Security style

D.

Access control

Expert Solution
Questions # 17:

Which one of the following /etc/snapmirror.conf entries will not support synchronous SnapMirror?

Options:

A.

FilerA:source_vol FilerB: destination_vol- sync

B.

FilerA: source_vol FilerB: destination_vol outstanding=3s sync

C.

FilerA: source_vol FilerB: destination_vol-0-55/5***

D.

FilerA: source_vol FilerB: destination_vol visibility_interval=1hr, outstanding=3ms, cksum=crc32 sync

Expert Solution
Questions # 18:

Which system is recommended as a secondary system for SnapVault?

Options:

A.

IS1200

B.

DataFort

C.

NearStore VTL

D.

FAS with NearStore license

Expert Solution
Questions # 19:

Which command allows yon to access the other nodes console after a takeover has occurred?

Options:

A.

toggle

B.

switch

C.

partner

D.

takeover

Expert Solution
Questions # 20:

Which statement describes the results of the snapmirror resync command?

Options:

A.

Resynchronization finds the newest common snapshot shared by the two volumes or qtrees, and removes all newer information on the storage appliance on which the command is run.

B.

Resynchronization will cause the loss of all data written to the destination after the original base snapshot was made.

C.

Resynchronization will update the snapshot on the source filer

D.

Resynchronization will update the snapshot on the destination filer.

Expert Solution
Viewing page 2 out of 6 pages
Viewing questions 11-20 out of questions