Pass the Cisco CCNP Enterprise 300-430 Questions and answers with ValidTests

AutoQoS simplifies the deployment of QoS by automating the process. On the Cisco Catalyst 9800 Series Wireless Controller, AutoQoS takes into account the characteristics of wireless traffic and helps in implementing a consistent QoS policy across both wired and wireless parts of the network. References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide.

The issue with the Cisco CMX dashboard not showing any data can be resolved by integrating the Wireless LAN Controllers (WLCs) with the CMX system. The CMX solution relies on data from the WLCs to track and detect users’ presence in the office area. Without the WLCs being added to CMX, the system cannot collect the necessary analytics and location data for its operations.

 In FlexConnect deployments with local switching, dynamic VLAN assignments are facilitated by Cisco ISE through the use of specific RADIUS attributes. The Tunnel-Private-Group-ID attribute is essential for communicating the VLAN ID to the access point, which then applies it to the wireless client after successful authentication.

References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide

The maximum time range that can be viewed on the Cisco DNA Center issues and alarms page is 24 hours. This allows network administrators to monitor and troubleshoot recent issues and alarms within a one-day period. References := (CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide)

To offer indoor directions to patient rooms using the existing wireless infrastructure, the hospital would need to install Cisco MSE (B) and Cisco CMX Visitor Connect ©. Cisco Mobility Services Engine (MSE) provides advanced location services, including tracking for Wi-Fi clients, which is essential for indoor navigation. Cisco CMX Visitor Connect, part of the Cisco Connected Mobile Experiences (CMX) solutions, allows for the customization of visitor experiences, such as indoor navigation. References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide.

The angle of arrival (AoA) method for client tracking determines the location of a wireless device using triangulation. This technique involves measuring the angle at which the signal arrives at different receivers (access points) and using this information to pinpoint the device’s location within the network. References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide

A Public-Signed SAN (Subject Alternative Name) certificate allows multiple domain names to be protected with a single certificate. This is useful in a distributed environment like a guest portal on Cisco ISE, where there may be multiple nodes with different Common Names (CNs). Using a SAN certificate can prevent CN mismatch errors during SSL/TLS handshakes. References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide

For the MSE to communicate with the Cisco Wireless LAN Controller (WLC) over NMSP when installed on a different network, the necessary configuration is to allow TCP/16113 port on the firewall. NMSP uses TCP port 16113 for its communications, and opening this port on the firewall will enable the MSE and WLC to establish a connection and communicate effectively. References := (CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide)

The command cmxha convert backup is used on the backup Cisco CMX server to designate it as the secondary server in a high-availability deployment. This command helps to resolve the issue where both servers are considered primary. References: Cisco CMX high-availability documentation will provide more details on this command.

The correct command to add a VLAN with a specific ID to a FlexConnect group in a Cisco Wireless LAN Controller (WLC) is ‘config flexconnect group BranchA-FCG vlan 30 add’. This command specifies the FlexConnect group name ‘BranchA-FCG’ and the VLAN ID ‘30’, followed by the action ‘add’, which is consistent with Cisco’s CLI syntax for WLC configuration. References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide