Summer Sale Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: pass65

Pass the Cisco CCNP Data Center 300-615 Questions and answers with ValidTests

Exam 300-615 All Questions
Exam 300-615 Premium Access

View all detail and faqs for the 300-615 exam

Viewing page 1 out of 5 pages
Viewing questions 1-10 out of questions
Questions # 1:

Refer to the exhibit.

The FCoE traffic fails to traverse the vfc2 interface. The VSAN 102 is configured for vfc2. Which action resolves the issue?

Options:

A.

Enable LLDP on the interface vfc2

B.

Activate DCBX on the N9K switch

C.

Activate DCBX on the interface e101/1/2

D.

Enable LLDP on the neighbor switch

Expert Solution
Questions # 2:

Question # 2

Refer to the exhibit. A functioning trunk port Ethernet1/48 exists between two identical Cisco Nexus 5000 Series Switches. The interfaces on the switches support the MACsec feature and are configured identically. To enable manual MACsec, an engineer adds the configuration shown in the exhibit to both sides of the trunk. The trunk port stops functioning. Which action should be taken to resolve the issue?

Options:

A.

Disable and then enable the port

B.

Enable the license for the trunk ports to support MACsec

C.

Lower the MTU value to less than 9216 bytes

D.

Configure the PMK with a length of 2048 bytes

Expert Solution
Questions # 3:

NO: 55

Question # 3

Refer to the exhibit. customer reports that all Intra-EPG isolation stopped working within a bare-metal tenant. Postman is running on a machine to get information from the APIC in case of orchestration failure. Which action resolves the issue?.

Options:

A.

B. Match encap="vlan-10" and primaryEncap="vlan-110"

B.

C. Modify the GET command to reference the valid path for the managed object

C.

D. Change pcEnfPref="unenforced" to pcEnfPref="enforced".

Expert Solution
Questions # 4:

An engineer is implementing a new BGP peering in their new data center. The engineer set up the BGP session that peers with the remote end. As soon as the BGP peers attempt to exchange routing prefixes, one of the BGP peers drops the connection. After reviewing the configuration, the engineer reviews the logging messages. The engineer discovers that the router is missing keepalives from the remote end and terminates the session. Which action resolves the issue?

Options:

A.

Set the bgp transport path-mtu-discovery attribute on both peers

B.

Set the higher values for the BGP keepalive and hold-down timers on both peers

C.

Configure the matching BGP AS numbers between the peers

D.

Configure the matching BGP passwords between the peers

Expert Solution
Questions # 5:

Refer to the exhibit A network administrator must provide Bash shell access to the support team for all of the Cisco Nexus 9000 Series Switches. The newly created user that is named "bashusers" fails to access the Bash shell. Which action resolves the issue?

Options:

A.

Associate bashusers with the Cisco NX-OS vdc-admin role and activate the nxapi feature.

B.

Associate bashusers with the Cisco NX-OS dev-ops role and activate the bash-shell feature.

C.

Associate bashusers with the Cisco NX-OS network-admin role and activate the guestshell feature.

D.

Associate bashusers with the Cisco NX-OS network-operator role and activate the bash-shell feature.

Expert Solution
Questions # 6:

Refer to the exhibit.

Question # 6

The vPC neighborship between two switches is in suspended state. Which configuration change resolves the issue and brings up the vPC neighborship?

Options:

A.

Change STP Port Type to Network on the peer switch

B.

Enable Bridge Assurance on the local switches

C.

Configure QoS MTU value of 9216 on the peer switch

D.

Add VLAN 400-401 to the configuration on the local switch

Expert Solution
Questions # 7:

A Cisco Nexus 9000 Series Switch crashes and fails to boot. An engineer must recover the switch and investigate the issue. The switch uses 172.20.50.213/24 IP address for management and its default gateway is 172.20.50.254. Drag and drop the steps for recovering the Cisco Nexus 9000 Series Switch from the left onto the right. Not all steps are used.

Select and Place:

Question # 7

Options:

Expert Solution
Questions # 8:

Refer to the exhibit.

Question # 8

HSRP adjacency fails to form between Nexus7K-1 and Nexus7K-2. Which action should be taken to solve the problem?

Options:

A.

Configure preempt on one of the switches in the HSRP group.

B.

Configure the same HSRP priority between the two switches.

C.

Configure the correct subnet mask on Nexus7K-1.

D.

Configure HSRP version 2 on Nexus7K-2.

Expert Solution
Questions # 9:

An engineer is troubleshooting a failed DCBX exchange between a server and a Cisco Nexus switch. Which action allows DCBX to successfully negotiate?

Options:

A.

Enable ETS

B.

Enable PFC.

C.

Enable Cisco Discovery Protocol.

D.

Enable LLDP.

Expert Solution
Questions # 10:

An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a “resolve slot” warning. Which server maintenance action resolves the issue?

Options:

A.

Perform diagnostic interrupt on the server.

B.

Re-acknowlegement the server.

C.

Reset the server.

D.

Decomission the server.

Expert Solution
Viewing page 1 out of 5 pages
Viewing questions 1-10 out of questions