Pass the CWNP CWNA CWNA-109 Questions and answers with ValidTests

The solution that you recommend is an Overlay WLAN monitoring solution. An Overlay WLAN monitoring solution is a system that uses dedicated sensors or probes to monitor the WLAN performance over time. The sensors are deployed throughout the WLAN coverage area and collect data on various metrics such as signal strength, noise level, channel utilization, interference, throughput, latency, packet loss, and QoS. The sensors send the data to a centralized server or appliance that analyzes the data and provides a single pane of glass for administration and monitoring of the solution. An Overlay WLAN monitoring solution can help to detect and troubleshoot WLAN issues, optimize WLAN performance, and generate reports and alerts. References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 538; [CWNA: Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 508.

The common spectrum analyzer view that you should use for this analysis is the Waterfall/Spectrogram view. The Waterfall/Spectrogram view shows the signal from the interfering device over time on a three-dimensional graph. The x-axis represents frequency, the y-axis represents time, and the z-axis represents amplitude or power. The color of each pixel indicates the signal strength at a given frequency and time. The Waterfall/Spectrogram view can help you identify the characteristics of the interference source, such as its frequency range, duty cycle, modulation type, and pattern. References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 524; [CWNA: Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 494.

https://7signal.com/802-11ac-migration-part-2-whats-nobodys-telling-you-about-80mhz-and-160mhz-channel-bonding

The clients are all 802.11n STAs or lower is the likely cause of this behavior. If a WLAN with 100 802.11ac access points is configured to use 80 MHz channels, butonly 40 MHz communications are seen in a particular BSS, it means that the clients in that BSS do not support 80 MHz channels. This could be because they are using older standards, such as 802.11n or lower, that do not support 80 MHz channels. Alternatively, they could be using newer standards, such as 802.11ac or ax, but have their channel width settings limited to 40 MHz or lower due to device capabilities or configuration options. In either case, the AP will adapt to the client’s channel width and use only 40 MHz of the 80 MHz allocated bandwidth to communicate with them. This will reduce the potential throughput and efficiency of the WLAN. References: , Chapter 3, page 111; , Section 3.2

The statement that in modern networks, both centralized and distributed data forwarding work well for most standard office deployments is true about WLAN performance. Data forwarding refers to how wireless frames are transmitted from wireless clients to wired networks or vice versa through wireless access points (APs). Centralized data forwarding means that all wireless frames are sent to a central controller or gateway before being forwarded to their destinations. Distributed data forwarding means that wireless frames are forwarded directly by the APs to their destinations without going through a central controller or gateway. Both methods have their advantages and disadvantages, depending on the network size, topology, traffic pattern, security, and management requirements. However, in modern networks, both methods can achieve high performance and scalability for most standard office deployments, as they can leverage advanced features such as fast roaming, load balancing, quality of service, and encryption. The other statements about WLAN performance are false. In most WLANs, special skill or tuning is required to get peak performance, such as selecting the appropriate channel, power, data rate, and antenna settings. WLANs perform worse as more wireless clients connect with each AP, as they cause more contention and interference on the wireless medium. To get the best performance out of an AP, you should not disable data rates of 72 Mbps and lower, as they are needed for backward compatibility and range extension. References: CWNA-109 Study Guide, Chapter 9: Wireless LAN Architecture, page 2811

The final step in an effective troubleshooting process is to document the results. Documentation is essential for keeping track of the problem history, the actions taken, the solutions implemented, and the outcomes achieved. Documentation can also help to prevent future problems, improve best practices, and provide feedback for improvement. Documentation should include relevant information such as problem description, symptoms, root cause analysis, resolution steps, verification methods, and lessons learned. References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 513; [CWNA: Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 483.

Granting access to specific network services or resources according to a user profile describes the authorization component of a AAA implementation. AAA stands for Authentication, Authorization, and Accounting, which are three functions that are used to control and monitor access to network resources and services. Authentication is the process of verifying that a user is who he says he is, by using credentials such as username, password, certificate, token, or biometric data. Authorization is the process of granting access to specific network services or resources according to a user profile, which defines the user’s role, privileges, and permissions. Accounting is the process of recording and reporting the usage of network services or resources by a user, such as the duration, volume, type, and location of the access. AAA can be implemented by using different protocols andservers, such as RADIUS, TACACS+, LDAP, Kerberos, or Active Directory. References: 1, Chapter 11, page 449; 2, Section 7.1

The power level at the Intentional Radiator (IR) is 250 mW. The IR is the point where the RF signal leaves the transmitter and enters the antenna system. To calculate the power level at the IR, we need to consider the output power level of the transmitter, the loss of the cable, and the gain of the antenna. The formula is:

Power level at IR (dBm) = Output power level (dBm) - Cable loss (dB) + Antenna gain (dBi)

We can convert the output power level of 50 mW to dBm by using the formula:

Power level (dBm) = 10 * log10(Power level (mW))

Therefore, 50 mW = 10 * log10(50) = 16.99 dBm

We can plug in the values into the formula:

Power level at IR (dBm) = 16.99 - 3 + 16 = 29.99 dBm

We can convert the power level at IR from dBm to mW by using the inverse formula:

Power level (mW) = 10^(Power level (dBm) / 10)

Therefore, 29.99 dBm = 10^(29.99 / 10) = 999.96 mW

However, since we need to round off the answer to the nearest integer value, we get:

Power level at IR (mW) = 1000 mW

References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 67; [CWNA: Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 57.

A 5 GHz channel should be used for this AP because channels 1 and 6 are 2.4 GHz channels and they have no impact on the decision. The 5 GHz frequency band offers more non-overlapping channels than the 2.4 GHz frequency band, which reduces interference and improves performance. The 5 GHz frequency band also supports higher data rates and wider channel bandwidths than the 2.4 GHz frequency band, which increases capacity and throughput. The 5 GHz frequency band also has less interference from other devices and sources than the 2.4 GHz frequency band, which enhances reliability and quality of service. Therefore, it is recommended to use the 5 GHz frequency band for WLANs whenever possible. Channels 1 and 6 are two of the three non-overlapping channels in the 2.4 GHz frequency band (the other one is channel 11). They are used by a neighbor network in this scenario, but they do not affect the channel selection for this AP because they operate in a different frequency band than the 5 GHz frequency band. Channel 6 is not always best to use; it depends on the interference and congestion level in the environment. Channel 1 is not best to use because it has a lower frequency than channel 6; frequency does not determine channel quality or performance. Channel 11 is not best to use because it is also a 2.4 GHz channel and it may interfere with channels 1 and 6. References: CWNA-109 Study Guide, Chapter 4: Antenna Systems and Radio Frequency (RF) Components, page 113

A POE device that requires 47 W of power should use the 802.3bt specification. This is because 802.3bt is the latest POE standard that supports up to 90 W of power delivery over four pairs of wires in an Ethernet cable. The previous POE standards, such as 802.3af and 802.3at, only support up to 15.4 W and 30 W of power delivery over two pairs of wires in an Ethernet cable, respectively. Therefore, they are not sufficient for powering a device that requires 47 W of power. The 802.11at specification does not exist; it is a typo or confusion with the 802.3at specification. References: CWNA-109 Study Guide, Chapter 8: Wireless LAN Access Points, page 2431

When performing a post-deployment validation survey for voice over Wi-Fi (VoWiFi), an action that must be performed is Application analysis with an active phone call on a VoWiFi handset. Application analysis is a method of testing the performance of a specific application over the WLAN by measuring parameters such as throughput, latency, jitter, packet loss, MOS score, and R-value. Application analysis with an active phone call on a VoWiFi handset can help to evaluate the quality of service (QoS) and user experience of VoWiFi calls over the WLAN. It can also help to identify any issues or bottlenecks that may affect VoWiFi calls such as interference, roaming delays, or insufficient coverage. References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 549; [CWNA: Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 519.