Pass the NFPA Fire Protection Specialist CFPS Questions and answers with ValidTests

The safety class for propane refrigerant R-290 is A3, which means it has no toxicity but high flammability. The safety class is determined by the ASHRAE Standard 34, which assigns a capital letter (A or B) for the toxicity level and a number (1, 2, or 3) for the flammability level of a refrigerant. Propane has a very low global warming potential and ozone depletion potential, but it also has a very low flash point and high auto ignition temperature, which make it highly flammable in the presence of ignition sources.References:Propane R-290 | Copeland US;R-290 Propane Refrigerant Fact & Info Sheet;Safety Data Sheet - Refrigerants; NFPA Fire Protection Handbook, 21st Edition, Chapter 3, Section 3.3.4.

The measurement of a fluid’s resistance to flow is calledviscosity.Viscosity is the property of a fluid that describes how easily it can deform or move when subjected to a shear stress, such as the force exerted by a pipe wall or a pump1. A fluid with high viscosity, such as honey, resists flow and requires more pressure to overcome the friction between its layers.A fluid with low viscosity, such as water, flows easily and has less frictional resistance2.Viscosity affects the hydraulic properties of water for fire protection systems, such as the flow rate, pressure loss, and pump power3. Viscosity is usually expressed in units of pascal-second (Pa s) or centipoise (cP) for liquids, and is dependent on the temperature and composition of the fluid.References:

Viscosity | Definition, Facts, Formula, Units, & Examples

Viscosity – The Physics Hypertextbook

Fire Pump Types | NFPA

[12.4: Viscosity and Laminar Flow; Poiseuille’s Law]

The correct answer is A. Type I construction consists of structural members of approved noncombustible or limited combustible materials with specified fire resistance ratings for exterior bearing walls of 3 or 4 hours. This is the highest level of fire resistance among the five types of construction defined by NFPA 220: Standard for Types of Building Construction.Type I construction is typically used for high-rise buildings made of concrete and protected steel12

The answer is A. According to NFPA 30: Flammable and Combustible Liquids Code, 2021 Edition, Chapter 14, lockers used for the storage of flammable or combustible liquids shall not exceed 1500 ft2 (139 m2) gross floor area. This limit applies to both indoor and outdoor lockers.Lockers are defined as self-contained, prefabricated structures that are designed to store hazardous materials and that are equipped with fire protection features, such as fire-resistance-rated walls, doors, and roofs, automatic sprinklers, spill containment, and ventilation12

According to NFPA 400, Table 5.2.1.1.3, the maximum allowable quantity (MAQ) of a nonliquified oxidizing gas per control area in an unsprinklered area is 2000 ft3 (56 m3) when stored in a gas cabinet. This quantity can be increased by 100% if the area is sprinklered or by 300% if the area is also provided with a gas detection system. A gas cabinet is a ventilated enclosure for the storage of one or more compressed gas containers that provides a method of control for potential leakage or fire exposure hazards [NFPA 400,3.3.32].References:NFPA 400, Table 5.2.1.1.3;NFPA 400, 3.3.32;NFPA 400, 5.2.1.1.3.1;NFPA 400, 5.2.1.1.3.2.

In the plastics industry, the four broad areas of processing arepolymerization,conversion,finishing, andrecycling1.Polymerization is the process of creating plastic resins from monomers or pre-polymers, using chemical reactions such as addition, condensation, or ring-opening2.Conversion is the process of transforming plastic resins into plastic products, using various methods such as injection molding, blow molding, extrusion, rotational molding, and thermoforming3.Finishing is the process of adding value to plastic products, such as coating, printing, welding, or assembling4.Recycling is the process of recovering plastic waste and converting it into new plastic products or raw materials, using mechanical, chemical, or biological methods5. Therefore,manufacturingis not one of the four broad areas of processing in the plastics industry, as it is a general term that encompasses all the stages of producing plastic products from raw materials.References:

Plastics Manufacturing: Types of Plastic and Processes - Deskera

Plastics industry - Wikipedia

Methods of Processing Plastic - Plastics Industry

Plastic recycling - Wikipedia

Polymerization - an overview | ScienceDirect Topics

The maximum allowable travel distance from any part of a smoke compartment to the door in a smoke barrier in a new health care facility is 200 ft. (60 m). This is based on NFPA 101: Life Safety Code, 2018 Edition, Chapter 18, Section 18.3.7.3, which states that “the travel distance from any point in a smoke compartment to reach a door in the required smoke barrier shall not exceed 200 ft (61 m).” A smoke compartment is a space within a building that is enclosed by smoke barriers on all sides, including the top and bottom. A smoke barrier is a continuous membrane, or a combination of materials, that is designed to restrict the movement of smoke.A smoke barrier door is a door assembly that is installed in a smoke barrier to allow access between smoke compartments123

The type of property classifications that experience the majority of fire deaths in the United States areone- and two-family dwellings.According to the NFPA, one- and two-family dwellings accounted for 64 percent of all civilian fire deaths in 2021, followed by apartments with 11 percent, and other residential properties with 1 percent1.One- and two-family dwellings are more vulnerable to fire fatalities because they often lack adequate fire protection systems, such as smoke alarms and sprinklers, and havemore potential sources of ignition, such as cooking, heating, and smoking2. Additionally, one- and two-family dwellings may have less escape routes, longer response times, and more occupants, especially children and elderly, who are at higher risk of fire death.References:

US Fire Loss in 2021 NFPA

Home Structure Fires - NFPA

[Fire Death Rate Trends: An International Perspective]

Computers and other information technology equipment are particularly susceptible to heat, steam, and combustion products, which can damage their sensitive components, cause data loss or corruption, and impair their functionality.Therefore, fire protection for IT equipment should consider the potential sources of heat, steam, and combustion products, such as electrical faults, flammable liquids, dust accumulation, water-based sprinklers, or smoke from adjacent areas, and implement appropriate measures to prevent, detect, and suppress fires, as well as to minimize the exposure of IT equipment to these hazards1234.References:Standard for the Fire Protection of Information Technology Equipment;Fire Protection of Computer Rooms—Legal Obligations and Best Practices - ISACA;Exploring Requirements for Information Technology Equipment;Demystifying IT room protection requirements - Consulting.