Pre-Summer Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: validbest

Pass the Cisco CCNP Enterprise 300-410 Questions and answers with ValidTests

Exam 300-410 All Questions
Exam 300-410 Premium Access

View all detail and faqs for the 300-410 exam

Viewing page 10 out of 13 pages
Viewing questions 136-150 out of questions
Questions # 136:

Refer to the exhibit.

Question # 136

An engineer configures SW101 to send OSPFv3 interfaces state change messages to the server. However, only some OSPFv3 errors are being recorded. which organization resolves the ..?

Options:

A.

snmp-server enable traps ospfv3 state-change if-state-change

B.

snmp-server-enable traps ospfv3 state-change restart-status-change

C.

snmp-server-enable traps ospfv3 state-change neighbor-state-change.

D.

snmp-server-enable traps ospfv3 state-change if-state-change neighbor-state-change

Expert Solution
Questions # 137:

Refer to the exhibits.

Question # 137

Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN. Which two

commands are missing? (Choose two.)

Options:

A.

The ip nhrp redirect command is missing on the spoke routers.

B.

The ip nhrp shortcut command is missing on the spoke routers.

C.

The ip nhrp redirect commands is missing on the hub router.

D.

The ip nhrp shortcut commands is missing on the hub router.

E.

The ip nhrp map command is missing on the hub router.

Expert Solution
Questions # 138:

What is the purpose of an OSPF sham-link?

Options:

A.

to allow intra-area routing when OSPF is used as the PE-CE connection protocol in an MPLS VPN network

B.

to correct OSPF backdoor routing when OSPF is used as the PE-CE connection protocol *i an MPLS VPN network

C.

to correct OSPF backdoor routing when OSPF is used as the PE-PE connection protocol m an MPLS VPN network

D.

to allow inter-area routing when OSPF is used as the PE-CE connection protocol in a MPLS VPN network

Expert Solution
Questions # 139:

Question # 139

Question # 139

Refer to the exhibit. The IT router has been configured with the Science VRF and the interfaces have been assigned to the VRF. Which set of configurations advertises Science-1 and Science-2 routes using EIGRPAS 111?

Question # 139

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Expert Solution
Questions # 140:

An engineer configured VRF-Lite on a router for VRF blue and VRF red. OSPF must be enabled on each VRF to peer to a directly connected router in each VRF. Which configuration forms OSPF neighbors over the network 10.10.10.0/28 for VRF blue and 192.168.0.0/30 for VRF red?

Question # 140

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Expert Solution
Questions # 141:

While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?

Options:

A.

The device must be resynced to Cisco DNA Center.

B.

The software image for the device is in install mode.

C.

The device has lost connectivity to Cisco DNA Center.

D.

The software image for the device is in bundle mode

Expert Solution
Questions # 142:

Question # 142

Refer to the exhibit. A network engineer configured routers R1 and R2 with MP-BGP. The engineer noticed that the routers cannot exchange any IPv6 routes, however, the IPv4 neighbor relationship is working fine. Which configuration must the engineer apply to router R2 to exchange IPv6 routes?

Options:

A.

Ipv6cef I Interface Loopback100Ipv6 address 2001: DB8:128::2/128 Interface GigabitEthernet1/0Ipv6 address 2001:DB8:1::2/64 I router bgp 65002no bgp default ipv4-unlcastneighbor 2001: DB8:1::1 emote-as 65001Iaddress-family ipv6network 2001:DB8:128::2/128neighbor 2001:DB8:1::1 activate

B.

Ipv6 unicast-routingipv6 cefInterface Loopback100ipv6 address 2001: DB8:12C:2 129Iinterface GigabitEthernet1/0ipv6 address 2001: DB8:1::2 64description AS65001 ID B466:A83D:3D7::1!router bgp 65002no bgp default Ipv4-unicastneighbor 2001: DB8:1::1 remote-as 65001!address-family Ipv4neighbor 2001:DB8:1::1 activate

C.

Ipv6 unicast-routingipvG cefIInterface Loopback100Ipv6 address 2001:DB8:128::2/128 I interface GigabitEthernet1/0ipv6 address 2001:DB8:1::2/64!router bgp 65002 no bgp default ipv4-unicast neighbor 2001: DB8:1::1 remote-as 65001 !address-family ipv6 network 2001:DB8:128::2I128

D.

Ipv6 unicast-routing Ipv6 cef Iinterface Loopback100 ipv6 address 2001: DB8:128::2/128 !interface GigabitEthernet1/0 ipv6 address 2001:DB8:1::2/64 irouter bgp 65002 no bgp default ipv4-unicast neighbor 2001: DB8:1::1 remote-as 65001 !address-family ipv6 network 2001:DB8:128::2/128 neighbor 2001:DB8:1::1 activate

Expert Solution
Questions # 143:

Refer to the exhibit.

Question # 143

Which configuration configures a policy on R1 to forward any traffic that is sourced from

the 192.168.130.0/24 network to R2?

Question # 143

Question # 143

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Expert Solution
Questions # 144:

Which 0S1 model is used to insert an MPLS label?

Options:

A.

between Layer 5 and Layer 6

B.

between Layer 1 and Layer 2

C.

between Layer 3 and Layer 4

D.

between Layer 2 and Layer 3

Expert Solution
Questions # 145:

In a DMVPN network, the Spoke1 user observed that the voice traffic is coming to Spoke2 users via the hub router. Which command is required on both spoke routers to communicate directly to one another?

Options:

A.

ip nhrp map dynamic

B.

ip nhrp shortcut

C.

ip nhrp nhs multicast

D.

ip nhrp redirect

Expert Solution
Questions # 146:

:591

Question # 146

Refer to the exhibit Which action fixes the OSPF routes redistribution into EIGRP?

Options:

A.

Match external type to type-1

B.

Set tags before matching into EIGRP

C.

Set a default metric in the route map

D.

Match OSPF and EIGR IDs

Expert Solution
Questions # 147:

Refer to the exhibit.

Question # 147

A network engineer finds that PC1 is accessing the hotel website to do the booking but fails to make payment. Which action resolves the issue?

Options:

A.

Allow stub network 10.10.202.168/30 on router R3 OSPF.

B.

Decrease the AD to 5 OSPF route 192.168.94.0 on R1.

C.

Increase the AD to 200 of static route 192.168.94.0 on R3.

D.

Configure a reverse route on R1 for PC1 172.16.1.0/24.

Expert Solution
Questions # 148:

Refer to the exhibit.

Question # 148

Network operations cannot read or write any configuration on the device with this configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)

Options:

A.

Configure SNMP rw permission in addition to community ciscotest.

B.

Modify access list 1 and allow operations subnet in the access list.

C.

Modify access list 1 and allow SNMP in the access list.

D.

Configure SNMP rw permission in addition to version 1.

E.

Configure SNMP rw permission in addition to community ciscotest 1.

Expert Solution
Questions # 149:

A network administrator is troubleshooting a high utilization issue on the route processor of a router that was reported by NMS The administrator logged into the router to check the control plane policing and observed that the BGP process is dropping a high number of routing packets and causing thousands of routes to recalculate frequently. Which solution resolves this issue?

Options:

A.

Police the cir for BGP, conform-action transmit, and exceed action transmit.

B.

Shape the pir for BGP, conform-action set-prec-transmit, and exceed action set-frde-transmit.

C.

Shape the cir for BGP. conform-action transmit, and exceed action transmit.

D.

Police the pir for BGP, conform-action set-prec-transmit, and exceed action set-clp-transmit.

Expert Solution
Questions # 150:

Question # 150

Refer to the exhibit. An engineer must troubleshoot a connectivity issue impacting the redistribution of the subnet 172.16.2.48/28 into the OSPF domain. Which configuration on router R1 advertises this subnet into the OSPF domain?

Options:

A.

R1(config)#route-map CCNP permit 10R1(config-route-map)#match route-type internalR1(config-router)#router ospf 10R1(config-router)#redistribute eigrp 100 subnets route-map CCNP

B.

R1(config)#route-map CCNP permit 10R1(config-route-map)#match route-type level-2R1(config-router)#router ospf 10R1(config-router)#redistribute eigrp 100 subnets route-map CCNP

C.

R1(config)#route-map CCNP deny 10R1(config-route-map)#match tag 200R1(config)#route-map CCNP permit 10R1(config-router)#router ospf 10R1(config-router)#redistribute eigrp 100 subnets route-map CCNP

D.

R1(config)#route-map CCNP permit 10R1(config-route-map)#match tag 200R1(config-route-map)#exitR1(config-router)#router ospf 10R1(config-router)#redistribute eigrp 100 subnets route-map CCNP

Expert Solution
Viewing page 10 out of 13 pages
Viewing questions 136-150 out of questions