What is the difference between IPv6 unicast and anycast addressing?
A network engineer is installing an IPv6-only capable device. The client has requested that the device IP address be reachable only from the internal network. Which type of IPv6 address must the engineer assign?
Which Layer 2 switch function encapsulates packets for different VLANs so that the packets traverse the same port and maintain traffic separation between the VLANs?
Refer to the exhibit.
Traffic that is flowing over interface TenGigabitEthernet0/0 experiences slow transfer speeds. What is the reason for the issue?
What is the function of the controller in a software-defined network?
Refer to the exhibit.
An engineer is configuring an EtherChannel using LACP between Switches 1 and 2 Which configuration must be applied so that only Switch 1 sends LACP initiation packets?
Refer to the exhibit.
Which route must be configured on R1 so that OSPF routing is used when OSPF is up. but the server is still reachable when OSPF goes down?
A Cisco engineer is configuring a factory-default router with these three passwords:
• The user EXEC password for console access is p4ssw0rd1
• The user EXEC password for Telnet access is s3cr3t2
• The password for privileged EXEC mode is pnv4t3p4ss Which command sequence must the engineer configured
A)
B)
C)
D)
A network administrator is setting up a new IPv6 network using the 64-bit address 2001 0EB8 00C1 2200:0001 0000 0000 0331/64 To simplify the configuration the administrator has decided to compress the address Which IP address must the administrator configure?
Drag and drop the characteristics of networking from the left onto the networking types on the right.
What is a requirement for nonoverlapping Wi-Fi channels?
Refer to the exhibit.
Router R1 currently is configured to use R3 as the primary route to the Internet, and the route uses the default administrative distance settings. A network engineer must configure R1 so that it uses R2 as a backup, but only if R3 goes down. Which command must the engineer configure on R1 so that it correctly uses R2 as a backup route, without changing the administrative distance configuration on the link to R3?
An engineer is configuring remote access to a router from IP subnet 10.139.58.0/28. The domain name, crypto keys, and SSH have been configured. Which configuration enables the traffic on the destination router?
A)
B)
C)
D)
A Cisco engineer must configure a single switch interface to meet these requirements
• accept untagged frames and place them in VLAN 20
• accept tagged frames in VLAN 30 when CDP detects a Cisco IP phone
Which command set must the engineer apply?
A)
B)
C)
D)
Refer to the exhibit.
Which two commands must be added to update the configuration of router R1 so that it accepts only encrypted connections? (Choose two )
Drag and drop the statements about networking from the left onto the corresponding networking types on the right.
Which protocol is used for secure remote CLI access?
Refer to the exhibit.
An engineer has started to configure replacement switch SW1. To verify part of the configuration, the engineer issued the commands as shown and noticed that the entry for PC2 is missing. Which change must be applied to SW1 so that PC1 and PC2 communicate normally?
A)
B)
C)
D)
An engineer must configure R1 for a new user account. The account must meet these requirements:
* It must be configured in the local database.
* The username is engineer.
* It must use the strongest password configurable. Which command must the engineer configure on the router?
Refer to the exhibit.
Routers R1 and R3 have the default configuration The router R2 priority is set to 99 Which commands on R3 configure it as the DR in the 10.0 4.0/24 network?
Refer to the exhibit.
Which plan must be Implemented to ensure optimal QoS marking practices on this network?
What is one reason to implement LAG on a Cisco WLC?
OSPF must be configured between routers R1 and R2. Which OSPF configuration must be applied to router R1 to avoid a DR/BDR election?
Refer to the exhibit.
Traffic sourced from the loopback0 Interface is trying to connect via ssh to the host at 10.0.1.15. What Is the next hop to the destination address?
Refer to the exhibit.
An engineer is configuring a new router on the network and applied this configuration. Which additional configuration allows the PC to obtain its IP address from a DHCP server?
Refer to the exhibit.
An engineer is updating the R1 configuration to connect a new server to the management network. The PCs on the management network must be blocked from pinging the default gateway of the new server. Which command must be configured on R1 to complete the task?
Refer to the exhibit.
Packets received by the router from BGP enter via a serial interface at 209 165 201 1 Each route is present within the routing table Which interface is used to forward traffic with a destination IP of 10.1.1.19?
Which WLC interface provides out-of-band management in the Cisco Unified Wireless Network Architecture?
Refer to the exhibit.
Which IP route command created the best path for a packet destined for 10.10.10.3?
Which is a fact related to FTP?
What differentiates the Cisco OfficeExtend AP mode from FlexConnect AP mode?
What Is the path for traffic sent from one user workstation to another workstation on a separate switch In a Ihree-lter architecture model?
Where is the interface between the control plane and data plane within the software-defined architecture?
A packet is destined for 10.10.1.22. Which static route does the router choose to forward the packet?
Which two protocols must be disabled to increase security for management connections to a Wireless LAN Controller? (Choose two )
Which two capabilities of Cisco DNA Center make it more extensible as compared to traditional campus device management? (Choose two.)
An engineer must configure a WLAN using the strongest encryption type for WPA2- PSK. Which cipher fulfills the configuration requirement?
Refer to the exhibit.
Which switch becomes the root bridge?
A)
B)
C)
D)
Refer to Exhibit.
How does SW2 interact with other switches in this VTP domain?
Refer to the exhibit.
Which minimum configuration items are needed to enable Secure Shell version 2 access to R15?
A)
B)
C)
D)
Refer to the exhibit.
A network engineer must update the configuration on Switch2 so that it sends LLDP packets every minute and the information sent via LLDP is refreshed every 3 minutes Which configuration must the engineer apply?
A)
B)
C)
D)
Physical connectivity is implemented between the two Layer 2 switches, and the network connectivity between them must be configured
1. Configure an LACP EtherChannel and number it as 1; configure it between switches SW1 and SVV2 using interfaces Ethernet0/0 and Ethernet0/1 on both sides. The LACP mode must match on both ends
2 Configure the EtherChannel as a trunk link.
3. Configure the trunk link with 802.1 q tags.
4. Configure the native VLAN of the EtherChannel as VLAN 15.
Refer to the exhibit. Drag and drop the learned prefixes from the left onto the preferred route methods from which they were learned on the right.
Refer to the exhibit.
Site A was recently connected to site B over a new single-mode fiber path. Users at site A report Intermittent connectivity Issues with applications hosted at site B. What is the reason for the problem?
Which function is performed by DHCP snooping?
A packet is destined for 10.10.1.22. Which static route does the router choose to forward the packet?
Refer to the exhibit.
Which command configures a floating static route to provide a backup to the primary link?
Which WPA3 enhancement protects against hackers viewing traffic on the Wi-Fi network?
Refer to the exhibit.
With which metric was the route to host 172.16.0.202 learned?
Which communication interaction takes place when a southbound API Is used?
