Pass the Cisco CCNP Service Provider 350-501 Questions and answers with ValidTests

https://www.cisco.com/c/en/us/support/docs/quality-of-service-qos/qos-policing/19645-policevsshape.html

 The “show cef interface” command is used to display per-interface statistics about Unicast Reverse Path Forwarding (uRPF) drops and suppressed drops. uRPF is a feature that helps to mitigate problems caused by IP address spoofing, and the “show cef interface” command provides detailed information on the interfaces where uRPF is applied, including drop statistics.

 The command “show mpls traffic-engineering tunnels” is used to quickly check the path of a TE (Traffic Engineering) tunnel in a Cisco MPLS core network. This command provides detailed information about each TE tunnel, including its current operational status, configuration details, and the specific path it is taking through the network. References: Implementing and Operating Cisco Service Provider Network Core Technologies source documents or study guide

The mpls ldp graceful-restart command is applied in the global configuration mode in IOS XE Software. This command enables MPLS LDP Graceful Restart, which assists a neighboring router with MPLS LDP Stateful Switchover/Nonstop Forwarding (SSO/NSF) Support and Graceful Restart to recover gracefully from an interruption in service without losing its MPLS forwarding state1.

References: MPLS Configuration Guide, Cisco IOS XE 17.x1.

: In this scenario, E-LINE pseudowires are suitable because they create a point-to-point Ethernet connection between the two sites. E-LINE pseudowires are commonly used for point-to-point Ethernet services.

References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) v1.0

RSVP-TE Fast Reroute (FRR) is a mechanism that provides protection switching for MPLS TE LSPs. The Point of Local Repair (PLR) will prefer to use a next-hop (NHOP) backup tunnel over a next-next-hop (NNHOP) backup tunnel when both are available. This preference is due to the fact that NHOP backup tunnels can provide faster rerouting around the failure point, minimizing traffic disruption and packet loss.

References: The information is based on the RSVP-TE FRR deployment considerations from the Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course materials.

To direct traffic from R3 to R4 via R1, the weight attribute on R3 can be set higher for the route through R1 compared to other routes. Weight is a Cisco-specific BGP attribute that determines the preferred path when multiple routes to the same destination exist. It is local to the router on which it is configured and not advertised to other BGP peers.

References :=

Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course materials.

MPLS TE FRR (Fast ReRoute) provides backup protection by creating a bypass LSP for each protected LSP at each point of local repair. This method allows for rapid switching to the backup path in case of a failure, minimizing traffic loss and disruption.

References :=

Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) course materials.

The core component of MDT that describes the data streamed to a collector is the encoder. In the context of Microsoft Deployment Toolkit (MDT), the encoder is not explicitly mentioned; however, the concept aligns with the process of creating and capturing images of operating systems, which involves encoding or compiling the necessary data into a deployable image.

 The issue is that the R2 Serial 1/0 interface is configured with an IP address, but the R1 Serial 1/0 interface is unnumbered. In OSPF, for two routers to form a neighbor relationship, they must be able to communicate on the same subnet. If one interface is unnumbered and the other has an IP address, they won’t be able to form a neighbor relationship, leading to OSPF prefixes missing from the routing table. References: Implementing and Operating Cisco Service Provider Network Core Technologies (SPCOR) - OSPF Configuration Guide

The Internet gateway router being connected as a PE router to the MPLS backbone is a design attribute that can be used to provide Internet access to a major customer through a separate dedicated VPN. This setup allows for efficient routing and separation of traffic, ensuring security and performance.

To complete the launch of the new internet service, ISP_A needs to ensure that routes are shared between different VRFs for Customer_A and Customer_B. Importing route-target 62:101 into the customer VRFs on R1 and R3 allows for the exchange of routes between these VRFs, facilitating the necessary connectivity for the new service. References := Cisco SPCOR