Summer Certification Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: validbest

Pass the Cisco CCNP Service Provider 350-501 Questions and answers with ValidTests

Exam 350-501 All Questions
Exam 350-501 Premium Access

View all detail and faqs for the 350-501 exam

Viewing page 9 out of 11 pages
Viewing questions 121-135 out of questions
Questions # 121:

Drag and drop the functions from the left onto the Path Computation Element Protocol roles on the right.

Question # 121

Options:

Expert Solution
Questions # 122:

Question # 122

Refer to the exhibit. ISP A provides MPLS L3VPN service to customer A with BGP as the external routing protocol. Customer A has just opened a new branch office in London and requested the service provider to implement lossless service between its two offices. The LDP is enabled over the MPLS backbone and label exchange is working normally. Which action must the ISP engineering team take to enable the service?

Options:

A.

Configure LDP and redistribute the route from EIGRP.

B.

Configure BGP address family VPNv4.

C.

Configure IGP and redistribute the route from BGP.

D.

Configure IGP LDP synchronization

Expert Solution
Questions # 123:

Question # 123

Refer to the exhibit an engineer working for a private telecommunication company with an employee Id: 4065:96:080 upgrades the WAN link between routers ASBR-101 and ASBR-201 to 1Gb by Installing a new physical connection between the Gi3 Interfaces. Which BGP attribute must the engineer configure on ASBR-201 so that the existing WAN link on Gi2 Is maintained as a backup?

Question # 123

Question # 123

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Expert Solution
Questions # 124:

Refer to the exhibit:

Question # 124

R1 and R2 are directly connected with Fast Ethernet interfaces and have the above configuration applied OSPF adjacency is not formed. When the debug ip ospf hello command is issued on R1. these log messages are seen.

Question # 124

Which command can be configured on routers R1 and R2 on fO/O interfaces to form OSPF adjacency?

Options:

A.

ip ospf network non-broadcast

B.

ip ospf network point-to- multipoint non-broadcast

C.

ip ospf network point-to-point

D.

ip ospf network broadcast

Expert Solution
Questions # 125:

Refer to Exhibit.

Question # 125

A network engineer is trying to retrieve SNMP MIBs with RESTCONF on the Cisco switch but fails. End-to-end routing is in place. Which configuration must the engineer implement on the switch to complete?

Options:

A.

netconf-yang cisco-ia snamp-community -string Public

B.

snmp-server community cisco RW

C.

snmp-server community public RO

D.

netconf-yang cisco-Ia snmp-community-string Private

Expert Solution
Questions # 126:

A network operator working for a telecommunication company with an employee Id: 4065 96080 it trying to implement BFD configuration on an existing network of Cisco devices Which task must the engineer perform to enable BFD on the interfaces?

Options:

A.

Disable Cisco Express Forwarding on the interfaces

B.

Disable SSO on the interfaces

C.

Remove any static routes that point to the interfaces

D.

Remove the log option from any ACLs on the interfaces.

Expert Solution
Questions # 127:

A regional MPLS VPN provider operates m two regions and wants to provide MPLS L 3VPN service for a customer with two sites in these separate locations. The VPN provider approaches another organization to provide backbone carrier services so that the provider can connect to these two locations.

Which statement about this scenario is true?

Options:

A.

When edge routers at different regional sites are connected over the global carrier backbone, MP-eBGP must run between the routers to exchange the customer VPNv4 routes

B.

When eBGP is used for label exchange using the send label option, MPLS-BGP forwarding is configured under the global ABC CSC PE-to CE interface

C.

When IGP is used for route exchange and LDP for label exchange, MPLS is enabled only on the VRF interface on the backbone-earner PE side.

D.

When BGP is used for both route and label exchange, the neighbor a.b.c.d send-lable command is used under the address family VPNv4 command mode.

Expert Solution
Questions # 128:

Refer to the exhibit.

Question # 128

A network operator has two IPv4 and IPv6 dual-stacked network on each side of the IPv4 core network. The operator must be able to provide connectivity between them while using specific assigned IPv6 space provided from the company IP administrator team. Which technology should the network operator use to accomplish this goal?

Options:

A.

6rd

B.

NAT46

C.

DS-Lite

D.

NAT44

Expert Solution
Questions # 129:

Question # 129

Refer to the exhibit. Users in AS 65010 are connected with the application server in AS 65050 with these requirements:

AS 65010 users are experiencing latency and congestion to connect with application server 172.16.50.10.

AS 65030 must be restricted to become Transient Autonomous System for traffic flow.

Links connected to AS 65020 and AS 65040 are underutilized and must be used efficiently for traffic.

Which two configurations must be implemented to meet these requirements? (Choose two.)

Options:

A.

Apply the AS-Path route-map policy for traffic received from R3.

B.

Configure the route map to prepend the AS-Path attribute for R5-R3 BGP peering.

C.

Apply the MED route-map policy for traffic received from R4.

D.

Configure a higher Local preference for R5-R4 BGP peering.

E.

Configure the route map to set the MED 50 attribute for R5-R4 BGP peering.

Expert Solution
Questions # 130:

What occurs when a high bandwidth multicast stream is sent over an MVPN using Cisco hardware?

Options:

A.

The traffic uses the default MDT transmit the data Only if it is a (S, G) multicast route entry.

B.

A data MDT is created if is a Multicast route entries

C.

A data and default MDT are created to flood the multicast stream of all PIM-SM neighbors.

D.

A data MDT is created to allow for the best transmit through the core for multicast route entries.

Expert Solution
Questions # 131:

What is the purpose of RSVP tear messages?

Options:

A.

to notify the tail-end router of resource unavailability on the transit router

B.

to inform the headend router of LSP issues

C.

to reuse router resources for other reservation requests

D.

to confirm successful end-to-end resource allocation

Expert Solution
Questions # 132:

A network operator working for a private outsourcing company with an employee id: 4261:72:778 needs to limit the malicious traffic on their network. Which configuration must the engineer use to implement URPF loose mode on the GigabitEthernet0/1 interface?

Options:

A.

router(config)# interface gigabitethernet0/1

router(config-if)# ip address 192.168.200.1 255.255.255.0

router(config-if)# ip verify unicast source reachable-via any

router(config-if)# ipv6 address 2001:DB8:1::1/96

router(config-if)# ipv6 verify unicast source reachable-via any

B.

router(config)# interface gigabitethernet0/1

router(config-if)# ip address 192.168.200.1 255.255.255.0

router(config-if)# ip verify unicast source reachable-via rx

router(config-if)# ipv6 address 2001:DB8:1::1/96

router(config-if)# ipv6 verify unicast source reachable-via rx

C.

router(config)# interface gigabitethernet0/1

router(config if)# ip address 192.168.200.1 255.255.255.0

router(config-if)# ip verify unicast source reachable-via rx

router(config-if)# ipv6 address 2001:DB8:1::1/96

router(config-if)# ipv6 verify unicast source reachable-via any

D.

router(config)# interface gigabitethernet0/1

router(config-if)# ip address 192.168.200.1 255.255.255.0

router(config-if)# ip verify unicast source reachable-via any

router(config-if)# ipv6 address 2001:DB8:1::1/96

router(config-if)# ipv6 verify unicast source reachable-via rx

Expert Solution
Questions # 133:

Question # 133

Refer to the exhibit. An Ethernet access provider is configuring routers PE-1 and PE-2 to provide E-Access EVPL service between UNI and ENNI. ENNI service multiplexing is based on 802.1ad tag 150, and service-multiplexed UNI is based on 802.1q tag 10. Which EFP configurations must the provider implement on PE-1 and PE-2 to establish end-to-end connectivity between CE-1 and CE-2?

Options:

A.

On PE-1:

interface GigabitEthernet2

service instance 100 ethernet

encapsulation dot1ad 150

rewrite ingress tag pop 1 symmetric

On PE-2:

interface GigabitEthernet2

service instance 2 ethernet

encapsulation dot1q 10

B.

On PE-1:

interface GigabitEthernet2

service instance 100 ethernet

encapsulation dot1q 150

rewrite ingress tag pop 1 symmetric

On PE-2:

interface GigabitEthernet2

service instance 2 ethernet

encapsulation dot1q 10

C.

On PE-1:

interface GigabitEthernet2

service instance 100 ethernet

encapsulation dot1ad 150 dot1q 10

rewrite ingress tag pop 2 symmetric

On PE-2:

interface GigabitEthernet2

service instance 2 ethernet

encapsulation dot1q 10

D.

On PE-1:

interface GigabitEthernet2

service instance 100 ethernet

encapsulation dot1ad 150

rewrite ingress tag pop 1 symmetric

On PE-2:

interface GigabitEthernet2

service instance 2 ethernet

encapsulation dot1q 10

rewrite ingress tag pop 1 symmetric

Expert Solution
Questions # 134:

A network engineer is configuring a BGP route policy for the SUBNET prefix set. Matching traffic must be dropped, and other traffic must have its MED value set to 400 and community 4:400 added to the route. Which configuration must an engineer apply?

Question # 134

Question # 134

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Expert Solution
Questions # 135:

A network operator needs to implement PIM-SSM multicast configuration on customer's network so that users in different domains are able to access and stream live traffic. Which two actions must the engineer perform on the network

to make the streaming work? (Choose two.)

Options:

A.

Configure at least one MSDP peer on the network

B.

Enable IGMP version 2 at the interface lever.

C.

Enable PIM sparse mode on the device.

D.

Enable IGMP version 3 at the interface level.

E.

Enable PM dense mode on the device.

Expert Solution
Viewing page 9 out of 11 pages
Viewing questions 121-135 out of questions