Pass the Cisco CCNP Enterprise 300-425 Questions and answers with ValidTests

 In an auditorium seating 500 students with laptops, a high-density design model is appropriate. This model focuses on supporting a large number of devices in a concentrated area with sufficient coverage and bandwidth. It involves strategic AP placement, proper channel planning, and capacity planning to ensure all students have reliable wireless access. References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide Premium Edition and Practice

https://www.cisco.com/c/dam/en_us/solutions/industries/docs/education/cisco_wlan_design_guide.pdf

The IEEE 802.11k protocol is designed to enable radio resource measurement and neighbor list radio management packets. This protocol allows wireless devices to better understand their radio environment, which in turn supports real-time applications over wireless by enabling devices to make quicker and more informed decisions about roaming

To focus the coverage heat map on the desired coverage, the engineer should use the RSSI slider to set the heat map to the desired cutoff filter. This action will adjust the display to show only the signal levels that meet or exceed the specified RSSI value, effectively filtering out weaker signals and highlighting areas with sufficient coverage. References: Designing Cisco Enterprise Wireless Networks (ENWLSD 300-425)

 In an office environment with cubicles, signal propagation is most commonly affected by absorption. This is because the materials used in cubicle walls, such as fabric and other dense substances, tend to absorb the radio frequency (RF) signals used in WLANs, leading to attenuation.

For wireless clients to use the 5 GHz band when Client Band Select is enabled, certain conditions must be met. Channel bonding should be enabled on the WLAN to allow for wider channels, providing higher throughput available in the 5 GHz band. The client must receive an RSSI above the minimum threshold set for Band Select to steer them towards the 5 GHz band. Additionally, the client device must be dual-band capable to connect to both 2.4 GHz and 5 GHz bands. Co-channel interference levels and UNII-2 extended channels being enabled offer additional benefits but are not requirements for Band Select functionality. Having 802.11a enabled on WLAN is necessary for any operation on the 5 GHz band but does not specifically relate to ensuring clients use this band under Band Select policies.

References := (CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide Premium Edition and Practice)

The issue described indicates that there are more critical priority access points than the backup Cisco WLC can handle with its available licenses. Since there are only 10 licenses available and 7 access points are set to critical priority, not all of them can failover when the primary Cisco WLC is at full capacity. This oversubscription of critical priority access points prevents all of them from failing over as expected.

References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide

 To ensure the anchored traffic remains up if a single WLC in the high-availability cluster fails, the mobility MAC address for the high-availability cluster should be configured. This allows the APs to recognize the cluster as a single entity, maintaining the CAPWAP tunnel to the anchor WLC in the DMZ even if one of the WLCs in the cluster fails.

In high-density environments, such as stadiums or auditoriums, APs are often mounted under the seats to provide a controlled cell size with attenuation. This placement helps to manage the RF environment by providing attenuation of 6 dB to 20 dB, which can reduce co-channel interference and improve the user experience by ensuring a strong signal and minimizing noise from other cells.

When identifying network requirements, it’s important to consider the number of wireless devices that will need access to ensure sufficient capacity and coverage. The business type can influence the types of applications and services that will be used, which in turn affects the network design.

 For an active survey where the application requires a minimum RF of -73 dBm, the mobile device used for the survey should have a receiver sensitivity of -70 dBm or better. This ensures that the device is sensitive enough to detect the minimum required signal strength for the application to function properly.